Liquid Crystal Devices

  • Update:Apr 19, 2020
  • View:

High Contrast Thin Film Polarizers (TFP) are made using advanced Ion Beam Sputtering (IBS) coating technology. These thin film polarizers separate s- and p-polarization components of high energy laser beams. Due to very low losses they are perfect for

We are promoting laser lamps, galvos, marking heads, green laser pointers etc till the stock is sold out. Pleasee click here.

Achromatic Ferroelectric Liquid Crystal Devices

Sintec Optronics’ Ferroelectric Liquid Crystal (FLC) devices offer a significant performance advantage in optical shutter and rotator applications demanding the fastest optical response times available. FLC devices are designed for applications requiring active timing control of beam transmittance. Key features of our FLC devices include high-speed binary operation, high purity linear polarized output, and maximum extinction ratio performance. Since these devices are solid state – undesirable mechanical motion, associated noise, and vibration problems are eliminated. Our FLC devices require a DC-balanced AC drive signal, typically resulting in a 50% duty cycle operation. Our optional FC 5010 Controller is ideal for driving the devices for optimal performance (sold separately).

FLC Controller (FCS010)

The FCS010 is a two-channel liquid crystal controller specifically designed to drive our ferroelectric liquid crystal shutters and rotators. The FCS010 has two short-circuit protected output channels driven 180 degrees out of phase. The pre-configured controller waveforms are optimized for FLC devices. We can tailor the waveform to your specific needs based on application and purchased FLC device. The drive waveform is output through SMA connectors. The controller is 100% RoHS compliant and is powered by a separate 12V international power supply.

Features:

Technical specifications:

Achromatic FLC Rotator:

Retarder Material

Ferroelectric liquid crystal

Substrate Material

Fused silica

Wavelength Range

405-850 nm, custom ranges up to 2 microns

Transmitted Wavelength Distortion

λ/2 (P-V @ 633), [λ/10 (RMS @ 633)]

Surface Quality

60-40 scratch dig

Beam Deviation

≤ 5 arc min

Outside Diameter (mounted)

2.00 ± 0.005 in. please inquire about custom sizes

Clear Aperture

0.70 in.

Response Time (10-90% & 90-10%)

≤ 100 micro-sec at room temp, wavelength dependent

Operating Temperature

20°C to 30°C

Storage Temperature

0°C to 60°C

Driver Requirements

± 5 to 30 Volts, 50% duty cycle

Achromatic FLC Shutter:

Polarizer Material

Dichroic Polymer

Transmission

≥ 30% (typical - unpolarized light)

≥ 65% (typical - polarized light)

Wavelength Range

450-720 nm, custom ranges up to 2 microns

Transmitted Wavefront Distortion

λ/2 (P-V @ 633), [λ/8 (RMS @ 633)]

Contrast Ratio

≥ 200:1

Achromatic FLC Controller:

Dimensions

5.3 in. W x 5.3 in. L x 2.0 in. H, (13.5 cm W x 13.5 cm L x 5.1 cm H)

Number of LC Channels

Two, running identical programs 180, degrees out of phase

Output Waveform

Bipolar ± 15V peak voltage, ± 10V holding voltage

Amplitude Resolution

16-bit; 1 mV voltage resolution

Internal Drive

1 to 10,000 Hz, 50% duty cycle, frequency controlled by front-panel, 10-turn knob

 

Product Description

Diameter (in.)

Clear Aperture (in.)

Thickness (in.)

Part Number

Rotator

2.00 [50.8 mm]

0.70 [17.78 mm]

1.38 [19.05 mm]

STM-FPA-200-λ

Shutter

1.00 [25.4 mm]

0.37 [9.4 mm]

1.42 [36.07 mm]

STM-FCS-100-λ

2.00 [50.8 mm]

0.70 [17.78 mm]

1.13 [28.7 mm]

STM-FCS-200-λ

Controller

N/A

N/A

N/A

STM-FC010

OEM Liquid Crystal Variable Retarder

Sintec Optronics is pleased to announce a small, mounted liquid crystal family of products intended for space constrained or OEM applications. By removing the temperature control circuitry, the overall dimensions of the housing can be significantly reduced. For even tighter mechanical constraints, unmounted cells are also available with flying leads or custom connectors.

Features:

Technical specifications:

Retarder Material

Nematic liquid crystal

Substrate Material

Optical quality synthetic fused silica

Wavelength Range

450 - 1800 nm (specify)

Retardance Range

~30 nm to λ/2, custom ranges are available

Transmitted Wavefront Distortion

λ/2 (P‐V @ 633), [λ/8 (RMS @ 633)]

Surface Quality

80 - 50 scratch-dig

Beam Deviation

3 arc min

Reflectance (per surface)

0.5% at normal incidence

Diameter Tolerance

± 0.005 in.

Temperature Range

0°C to 50°C

Laser Damage Threshold

500 W/cm2, CW; 300 mJ/cm2, 10 ns, visible

 

Clear Aperture in. [mm]

Thickness in. [mm]

Diameter in. [mm]

Part Number

0.49 [12.5]

0.25 [6.35]

Ø1.00 [Ø25.4]

STM-LVT-100

 

MWIR Variable Retarder

Liquid crystal technology for polarization control now extends into the mid IR. Sintec Optronics standard line of polarization controllers can be used for these new variable retarders. They can be custom configured for use as variable attenuators and as polarization rotators.

Features:

Technical specifications:

Retarder Material

Nematic liquid crystal

Substrate Material

Anti-reflection coated germanium

Wavelength Range

3.6 µm to 5.7 µm

Maximum Retardance

1/2 λ at 4 µm*

Minimum Retardance

0.06 λ at 4 µm at 10 V

Reflectance

≤ 5% per external surface

Operating Temperature Range

0˚C to +50˚C

Response Times

< 500 msec

Clear Aperture in. [mm]

Diameter ± 0.005 in. [± 0.13 mm]

Thickness in. [mm]

Part Number

0.7 [17.8]

Ø2.00 [Ø50.8]

0.75 [19.1]

STM-LVR-200-λ

UV Liquid Crystal Variable Retarder

Liquid crystal technology for polarization control now extends into the ultraviolet. While standard LC materials are susceptible to UV light damage below 450 nm, Sintec Optronics has designed a new UV-resistant LCVR material capable of operating at lower wavelengths (as low as 350 nm). These parts can be custom configured for use as variable attenuators or polarization rotators and are compatible with our standard line of liquid crystal controllers.

Features:

Technical specifications:

Retarder Material

Nematic liquid crystal

Substrate Material

UV Grade Fused Silica

Wavelength Range

350-450 nm (specify)

Maximum Retardance*

1/2 λ at 400 nm

Minimum Retardance

0.06 λ at 400 nm (at 10 V)

Transmitted Wavefront Distortion

λ/4 (P-V @ 633), [λ/16 (RMS @ 633)]

Surface Quality

40-20 scratch-dig

Beam Deviation

2 arc min

Reflectance*

AR coatings are available

Diameter Tolerance

± 0.010 in.

Temperature Range

0˚C to +50˚C (Operating)

Clear Aperture in. [mm]

Thickness in. [mm]

Diameter in. [mm]

Part Number

0.37 [9.4]

1.23 [31.2]

Ø1.00 [Ø25.4]

STM-LVR-100-UV

0.7 [17.78]

0.75 [19.05]

Ø2.00 [Ø50.8]

STM-LVR-200-UV

Liquid Crystal Variable Attenuator

Sintec Optronics’ Liquid Crystal Variable Attenuator (LCVA) offers real-time, continuous control of light intensity. Our attenuator consists of an LC Variable Retarder (with attached compensator) operating between crossed linear polarizers. With crossed polarizers, light transmission is maximized by applying the correct voltage to achieve half-wave retardance from the LC cell as shown in figure 4-11. Half-wave operation rotates the incoming polarization direction by 90°, so that light is passed by the second polarizer. Minimum transmission is obtained with the retarder operating at zero (or a whole number of) waves. Transmission decreases as the applied AC voltage amplitude increases (half- to zero-waves retardance). The relationship between transmittance T and retardance (in degrees) for crossed polarizer configuration is given by: T(Θ) = 1/2 [1 - cos(Θ)] Tmax where Tmax is the maximum transmittance when retardance is exactly one-half wave (or 180°). Figure 4-12 shows transmittance as a function of applied voltage. Maximum transmission is dependent upon properties of the LC Variable Retarder as well as the polarizers used in your system. Figure 4-13 shows the transmission of an LC Variable Attenuator optimized for use at 550 nm with crossed polarizers. An unpolarized light source is used for illumination. Extinction ratio is defined as the maximum transmission (LC cell at half-wave) pided by the minimum transmission (LC cell at zero waves). Values exceeding 1000:1 (see figure 4-14) can be obtained for a single wavelength by optimizing the applied voltage levels for minimum and maximum transmission. We guarantee a minimum extinction ratio of 500:1 at your specified wavelength. A Liquid Crystal Variable Attenuator can be configured with high efficiency calcite or beamsplitting polarizers to maximize light transmittance and increase damage threshold. With a linearly polarized input beam and a calcite polarizer, transmittance values exceed 90% at most wavelengths. Very high extinction ratios, in excess of 5000:1, can be achieved with custom double attenuators. In this design, two Liquid Crystal Variable Retarders are combined with three polarizers.

Features:

Technical specifications:

Retarder Material

Nematic liquid crystal with Birefringent polymer

Polarizer Material

Dichroic polymer

Substrate Material

Optical quality synthetic fused silica

Wavelength Range

Visible

450-700 nm

Near Infrared 1

650-950 nm

Near Infrared 2

900-1250 nm

Near Infrared 3

1200-1700 nm

Contrast Ratio

500:1 at single wavelength

Transmitted Wavefront Distortion

≤ λ/4 (each component)

Surface Quality (scratch-dig)

40-20

Beam Deviation

≤ 2 arc min

Reflectance (per surface)

≤ 0.5% at normal incidence

Operating Temperature

0˚C to 50˚C

Laser Damage Threshold

1 W/cm2, CW (dichroic polarizers)

 

Clear Aperture in. [mm]

Diameter ± 0.005 in. [± 0.13 mm]

Thickness in. [mm]

Part Number

0.37

Ø1.00

1.23

STM-LVA-100-λ

[9.4]

[Ø25.4]

[31.2]

0.7

Ø2.00

0.75

STM-LVA-200-λ

[17.8]

[Ø50.8]

[19.1]

1.6

Ø3.00

1

STM-LVA-300-λ

[40.6]

[Ø76.2]

[25.4]

Liquid Crystal Polarization Rotator

Our Liquid Crystal Polarization Rotator (LPR) continuously rotates the polarization orientation of a monochromatic, linearly polarized input beam. Our LPR consists of a compensated Liquid Crystal Variable Retarder combined with a zero-order polymer quarter-wave retarder. The fast axis of the liquid crystal variable retarder is oriented at 45° to the slow axis of the quarter-wave retarder and the linearly polarized input must be parallel to the quarter-wave retarder slow axis. Polarization rotation is achieved by electrically controlling the retardance of the Liquid Crystal Variable Retarder, eliminating any mechanical motion. A quarter-wave retarder converts elliptical polarization formed by the Liquid Crystal Variable Retarder to linear polarization. The rotation angle is equal to one-half the retardance change from the Liquid Crystal Variable Retarder. Response time of the LPR depends upon the desired amount of rotation. Small rotations have a longer response time because of a smaller change in the electric field strength. Polarization purity is defined as the ratio of the rotated linear component to the orthogonal component and, on average, polarization purity (or extinction ratio) is better than 150:1. We provide test data including the required voltages corresponding to polarization orientations, in 10° increments, from approximately -40° to approximately 140° rotation. These measurements are taken at ambient temperature for your specified wavelength. Standard Liquid Crystal Polarization Rotators are supplied without an input polarizer. Input polarization direction must be precisely aligned for optimum performance.

Features:

Technical specifications:

Retarder Material

Nematic liquid crystal with Birefringent polymer

Substrate Material

Optical quality synthetic fused silica

Wavelength

450 -1800 nm (specify)

Polarization Rotation

180˚

Polarization Purity

150:1 average

Transmittance

> 92% with polarized input

Transmitted Wavefront Distortion

n ≤ λ/4

Surface Quality (scratch-dig)

40-20

Beam Deviation

≤ 2 arc-min

Reflectance (per surface)

≤ 0.5% at normal incidence

Operating Temperature

0˚C to +50˚C

Laser Damage Threshold

500 W/cm2, CW; 300 mJ/cm2, 10 ns, visible

 

Clear Aperture in. [mm]

Diameter ± 0.005 in. [± 0.13 mm]

Thickness in. [mm]

Part Number

0.37

Ø1.00

1.23

STM-LPR-100-λ

[9.4]

[Ø25.4]

[31.2]

0.7

Ø2.00

0.75

STM-LPR-200-λ

[17.8]

[Ø50.8]

[19.1]

1.6

Ø3.00

1

STM-LPR-300-λ

[40.6]

[Ø76.2]

[25.4]

High Contrast Optical Shutter

Our liquid crystal shutter uses twisted nematic liquid crystals to provide a vibration-free mechanical shutter alternative. The twisted nematic liquid crystal switches between a state that rotates the input polarization by 90° with no voltage applied and a state that makes no change in the input polarization with 8 to 10 volts applied. The applied voltage is a 2 kHz AC square-wave. The shutter is supplied with integral dichroic visible polarizers to provide an average extinction ratio of better than 1,000:1. Custom shutters with larger aperture sizes and with wavelength coverage to 2.1 microns are available on a custom basis.

Features:

Technical specifications:

Liquid Crystal Configuation

Twisted nematic

Substrate Material

Optical quality synthetic fused silica

Polarizer Material

Dichroic polymer

Wavelength Range

450-1800 nm

Contrast Ratio (average)

1,000:1

Acceptance Angle

25˚ incidence angle with some reduction above 10˚

Switching Time (10% to 90% at room temperature)

Closed to open:

5 milliseconds

Open to closed:

0.4 milliseconds

Transmitted Wavefront Distortion

≤ λ/2

Surface Quality (scratch-dig)

60-40

Beam Deviation

≤ 5 arc min

Reflectance (per surface)

≤ 0.5% at normal incidence

Laser Damage Threshold

1 W/cm2, CW

Glass Thickness

0.48-0.52 in.

Polarization Direction

Vertical on input face, horizontal on output face

Storage Temperature

-20˚C to +80˚C

Operating Temperature

0˚C to +50˚C

 

Clear Aperture in. [mm]

Diameter ± 0.005 in. [± 0.13 mm]

Thickness in. [mm]

Part Number

0.37

Ø1.00

1.23

STM-LCS-100

[9.4]

[Ø25.4]

[31.2]

0.7

Ø2.00

0.75

STM-LCS-200

[17.8]

[Ø50.8]

[19.1]

1.6

Ø3.00

1

STM-LCS-300

[40.6]

[Ø76.2]

[25.4]

Binary Liquid Crystal Rotator

An Optical Rotator is a two-state device used to rapidly switch between two orthogonal sites of linear polarization. One state has output linear polarization parallel to an input linear polarization state. This occurs when voltage is applied to the rotator. The other state has output polarization orthogonal to the input polarization and occurs when no voltage is applied. Sintec Optronics manufactures and sells liquid crystal based Optical Rotators for applications requiring active timing control of beam transmittance by using them in combination with high quality polarizers.  Key features of our Optical Rotators include high-speed binary operation, high purity linear polarized output, and maximum extinction ratio performance.  Since these devices are solid state – undesirable mechanical motion, associated noise, and vibration problems are eliminated. Binary LC Rotators deliver optimum extinction ratio performance, often greater than 10,000:1 across the visible wavelength range, when used with high quality polarizers.  Even higher extinction performance is achieved over narrower bandwidths or for single laser line applications.  Up to 100% duty cycle operation is standard. This Rotator has a broad operating temperature range, designed to meet applications requiring low cost components with negligible impact on performance.

Features:

Technical specifications:

Retarder Material

Twisted Nematic liquid crystal

Substrate Material

Optical quality synthetic fused silica

Wavelength Range

400 - 1800 nm

Transmitted Wavefront Distortion

λ/4 (P-V @ 633 nm), [λ/16 (RMS @ 633 nm)]

Response Time (VIS)

≤ 5 ms

Surface Quality

40-20 scratch-dig

Beam Deviation

2 arc min

Reflectance (per surface)

0.5% at normal incidence

Diameter Tolerance

± 0.010 in.

Operating Temperature Range

10°C to 60°C (Operating); -40°C to 90°C (Storage)

Laser Damage Threshold

500 W/cm2, CW; 300 mJ/cm2, 10 ns, visible

 

Diameter (in.)

Clear Aperture (in.)

Thickness (in.)

Part Number

1.00 [25.4 mm]

0.37 [9.4 mm]

1.23 [31.24 mm]

STM-LTN-100-λ

2.00 [50.8 mm]

0.70 [17.8 mm]

0.75 [19.05 mm]

STM-LTN-200-λ

We offer Binary LC Rotators to cover four spectral regions:

VIS: 450 – 700 nm

IR 1: 650 – 950 nm

IR 2: 900 – 1250 nm

IR 3: 1200 – 1700 nm

High Speed Liquid Crystal Variable Retarder

Sintec Optronics newest liquid crystal (LC) product, the high speed LC variable retarder (HS LCVR) has a 10X speed improvement over our award winning standard LCVR.  The sub-millisecond speeds are achieved without the 50/50 duty cycle drive scheme required by our ferroelectric liquid crystal components, but are nearly as fast.  The new LCVR uses nematic liquid crystal materials to electrically control polarization and provide tunable retardation by changing the effective birefringence of the material with applied voltage, thus altering the input polarized light to any chosen elliptical, linear or circular polarization. Our precision HS LCVR requires unique fabrication and assembly steps.  We construct these retarders using optically flat fused silica windows coated with our transparent conductive Indium Tin Oxide (ITO).  Our ITO coating is specially designed for maximum transmission from 400 – 700 nm. Liquid Crystal Variable Retarder response time depends on several parameters, including layer thickness, viscosity, temperature, variations in drive voltage and surface treatment.  Liquid crystal response time is proportional to the square of the layer thickness and therefore, the square of the total retardance.

Features:

Technical specifications:

Retarder Material

Nematic liquid crystal

Substrate Material

Optical quality synthetic fused silica

Wavelength Range

450 - 700 nm

Typical LC Rise Time (10 – 90%)

50 µs @ 532 nm

Typical LC Fall Time (90 – 10%)

500 µs @ 532 nm

Retardance

0 to λ/2

Transmitted Wavefront Distortion (at 632.8 nm)

≤ λ/4

Surface Quality

40-20 scratch-dig

Beam Deviation

≤ 2 arc min

Reflectance (per surface)

≤ 0.5% at normal incidence

Temperature Range

50°C

Recommended Safe Operating Limit

500 W/cm 2, CW; 300 mJ/cm2, 10 ns, visible

 

Diameter, D (in.)

Clear Aperture, CA (in.)

Thickness, t (in.)

Part Number

2

0.8

0.75

STM-HSLRC-200

Analog Liquid Crystal Controller

Sintec Optronics is excited to announce the release of the Model B1010, our new Analog Liquid Crystal Controller. This liquid crystal (LC) driver is designed to integrate with any single (standard) Meadowlark Optics LC device currently offered as well as any nematic Liquid Crystal device compatible with the specifications listed. Independent voltage settings allow easy and repeatable selection of two retardance values. Often, it is desirable to modulate between the two states. For example, switching between quarter-wave and three quarterwave retardance changes linearly polarized light between left and right circular. A manual toggle allows easy switching between two states. Banana jacks between the knobs allow for continuous voltage monitoring without interfering with LC device connections. Each Sintec Optronics Liquid Crystal Variable Retarder is supplied with a plot of its actual retardance versus voltage. Using your Model B1010 Controller and this retardance plot ensures accurate retardance to voltage correlation.

Features:

Technical specifications:

Output Voltage

0 to 20 VAC,  RMS, maximum

Fundamental Drive Waveform

2 kHz AC square wave

External Modulation (input)

none

Output Bias

± 10 mV DC

Power Requirements

12 VDC 200 mA or 9V battery external power supply included 100-240 VAC 50-60 Hz, 0.3 A International Plugs

Battery Life

1 hour (intended for convenience, not as a primary power source)

External Dimensions (W x D x H)

3.3 x 6.0 x 2.2 in.

Weight

< 1 lb.

CE Compliance

Compliant

 

Item

Part Number

Analog Liquid Crystal Controller

STM-B1010

B1010 Package

B1010 Controller Unit

Power Supply

SMA-BNC Adapter

Internal Plug Set

9 Volt Battery

User Manual

Two Channel High Voltage Interface

Our two Channel High Voltage Digital Interface is designed for independent high precision computer control of up to two Sintec Optronics Swift LC liquid crystal devices at one time. The D3060HV Package includes all the functionality of the D3050 plus the high voltage circuitry necessary for Swift LC devices. Also included is capability for temperature monitoring and control on one channel. The Advanced Package allows the amplitude of the 13 kHz square wave output to be driven either by an external signal supplied to a front panel connector or specific CellDRIVE generated waveforms including sinusoidal, square, triangle, sawtooth and transient nematic effect waveforms. Additional functions include the capability to output a sync pulse on a front panel connector at desired points in the CellDRIVE generated waveforms and the ability to save/restore all CellDRIVE settings to/from a file.

Features:

Technical specifications:

Fundamental Drive Waveform

13 kHz ac square wave

Modulation Amplitude

0-100 V rms

Modulation Resolution

10 mV (1.55 mV using LabVIEW™ subroutines)

DC Offset

< 50 mV

Communications Interface

USB or RS232

LC Cell to Controller Connections

LEMO™ RF cable, 2 m length

Power Requirements

100-240 V ac; 47-63 Hz; 2.5 A

Safety Feature

Keyed Interlock Switch

Modulation Waveforms

External modulation input (0-5 V)

Sinusoidal

Triangle

Square

Sawtooth

Transient nematic effect

Temperature Control

Active heating/passive cooling to within ± 1˚C of nominal set point

Sync Output

TTL, 1 µs pulse, user specified phase

Minimum System Requirements

USB or RS232 COM Port

Use of LavVIEW Instrument Library requires LabVIEW version 2010 or higher

 

Item

Part Number

High Voltage Controller

STM-D3060HV

High Voltage Cable

Swift LC Cable

 

Liquid Crystal Digital Interface Controller

The new D5020 Liquid Crystal Digital Interface is the next generation in the evolution of Sintec Optronics Liquid Crystal Controllers. The Digital Controller is designed for user functionality and productivity. The D5020 provides a “set and go” function that allows the controller to run autonomously without a computer. Controlling multiple Liquid Crystal cells has never been easier. CellDRIVE 5000 software provides a separate sync output for each channel as well as temperature sensing and control on both channels. The 2kHz square wave output can be amplitude modulated with sinusoidal, square, triangle, sawtooth and transient nematic effect waveforms.

Features:

Technical specifications:

Fundamental Drive Waveform

2 kHz AC square wave

Modulation Amplitude

0-10 V rms (20 V rms available)

Modulation Resolution

1 mV (0.155 mV using LabVIEW™ subroutines)

DC Offset

< 5 mV

Communications Interface

USB

LC Cell to Controller Connections

SMA-SMB, 2 m cable length

CE Compliance

Compliant

Modulation Waveforms

External modulation input (0-5 V)

Sinusoidal

Triangle

Square

Sawtooth

Transient nematic effect

Temperature Control (2 channels)

Active heating/passive cooling to within ± 1˚C of nominal set point

Sync Output

TTL, user specified phase

Minimum System Requirements

Windows™ Vista, 7 or 8

Requires LabVIEW™ version 2010 or higher for use with LabVIEW™

instrument library

 

Item

Part Number

LC Digital Interface

STM-D5020

LC Digital Interface (20V rms)

STM-D5020-20V

SMA to SMB Cables

STM-SMA-SMB

Sync Cables (SMB to BNC)

STM-SMB-BNC

LC Temperature Controller

The Sintec Optronics TC3051 is a single channel, microprocessor based temperature controller specifically designed to work with Meadowlark Optics’ liquid crystal devices equipped with the Temperature Sensing and Control (TSC) option. The TC3051 requires minimal setup: connect the included power supply, connect the temperature control cable to both the TC3051 and the liquid crystal device and turn the power on.

Features:

Technical specifications:

Power Requirements

100 – 240V ac, 47 – 63 Hz, 500 mA

Fuse

Internal (not user serviceable)

Environment

0° C to +50° C (Operating); -55°C to +100°C (Storage)

External Dimensions (W x D x H)

5.08 x 5.25 x 1.50 in. (12.90 x 13.33 x 3.81 cm)

Weight

lb. (0.45 kg)

Temperature Readout Resolution

1°C

Temperature Readout Range

0°C to 99°C

Setpoint Resolution

1°C

Setpoint Range

20°C to 60°C

 

Temperature Controller

STM-TC3051

Ferroelectric Liquid Crystal Controller

The FCS010 is a two‐channel liquid crystal controller specifically designed to drive our ferroelectric liquid crystal shutters and rotators. It has two short‐circuit protected output channels driven 180 degrees out of phase. The pre‐configured controller waveforms are optimized for FLC devices. We can tailor the waveform to your specific needs based on application and purchased FLC device. The drive waveform is output through SMA connectors. This controller is 100% RoHS compliant and is powered by a separate 12V international power supply.

Features:

Technical specifications:

Dimensions

5.3 in. W x 5.3 in. L x 2.0 in. H , (13.5 cm W x 13.5 cm L x 5.1 cm H)

Number of LC Channels

Two, running identical programs 180 degrees out of phase

Output Waveform

Bipolar  ±  15V peak voltage,  ±  10V holding voltage

Amplitude Resolution

16-bit; 1 mV voltage resolution

Internal Drive

1 to 10,000 Hz, 50% duty cycle, frequency controlled by front-panel 10-turn knob

 

Ferroelectric Liquid Crystal Controller

STM-FCS010

 Polarizser,  Waveplate Retarder,  Liquid Crystal Device,  Spatial Light ModulatorApplications of SLM

Share: